|Place of Origin:||CHINA|
|Certification:||UL , KC , IEC62133|
|Model Number:||AA1300 mAh 14.4V|
|Minimum Order Quantity:||1000|
|Packaging Details:||Standard Export Carton|
|Delivery Time:||10000 PCS Per Day|
|Type:||NI-MH Rechargeable Battery||Size:||AA|
|Application:||Emergency Lighting Use||Warranty:||3 Years|
|Cycle Life:||1000 Cycles||Battery Type:||NI-MN BATTERY|
2000mAh 1C NIMH Rechargeable Battery,
AA 14.4 NIMH Rechargeable Battery,
Nimh AA 14.4 Rechargeable Batteries
Nimh AA 14.4 2000mAh Batteries Light Weight For Emergency Lighting use
Nickel Metal Hydride Battery AA1300mAh 14.4V
Cell Size AA
Nominal voltage 12V
Typical Weight about 285 g(ref)
Capacity (20℃, discharge at 0.2Cto ccv=10.0V)
Typical 1300 mAh(ref)
Minimum 1300 mAh
Charging Condition charge at 130 mA for 16h
Tmax: (45～55) ℃
Time: charge capacity reach to 105% nominal capacity
Trickle charge 100mA~200mA (0.05 C ~0.1 C)
Max over-charge current 200 mA charge for 48 hrs
Discharge cut off voltage 10.0V
Maximum Discharge Current 2000mA(1C)
Storage(six month) -20℃~35℃
Storage(1 month) -20℃~45℃
Fast charge 10℃~45℃
Trickle charge 0℃~45℃
Unless otherwise stated, tests should be done within one month of delivery under the following conditions
Ambient Temperature:20±5℃ Relative Humidity:65±20%RH
Notes: Standard Charge/Discharge Condition:
Charge:200mA(0.1 C)×16 hrs Discharge:400mAh (0.2 C) to 10.0V/Pack
|Open circuit voltage||v||≥12.5||Standard Charge , 1hr rest||Pack|
|Internal impedance(Ri)||mΩ||≤450||Standard Charge , 1hr rest (1KHZ)||Pack|
Low Rate Discharge
|minute||≥300||Standard Charge , 1hr rest before discharge||Allow to 3 cycles|
High Rate Discharge
|minute||≥112||Standard Charge , 1hr rest before discharge||Allow to 3 cycles|
High Rate Discharge
|minute||≥51||Standard Charge , 1hr rest before discharge||Allow to 3 cycles|
No leakage nor
|0.1 C charge for 48 hrs|
Storage: 28 days at Ambient Temperature or 7 days at 45℃ Standard discharge
|IEC Cycles Test||Cycle||≥500||IEC 61951-2 (2011)/22.214.171.124||(see note 1)|
|Short Circuit||N/A||Leakage &deformation may occur, but no explosion is allowed||After standard charge.,short circuit the cell at 20+/-5℃ until the cell temperature returns to ambient temperature. (The resistance of the inter- connecting circuitry shall not exceed 0.1 ohm.)|
change of voltage:
change of internal
|Charge at 0.1C for 16hrs and then leave for 24hrs check battery before after vibration Amplitude: 1.5mm Vibration:3000CPM (any direction for 60mins)|
change of voltage:
change of internal
|Charge at 0.1C for 16hrs and then leave for 24hrs check battery before/ after drop Height: 100cm Thickness of the wooden board: 30mm Direction is not specified Test for 3 times|
1. Approximate charge time from discharged rate, for reference only IEC 61951-2(2011)
IEC61951-2(2011) /126.96.36.199Cycle Life Test:
|1||0.1C,16h||none||0.25 C,2h 20min|
|2—48||0.25 C,3h 10min||none||0.25 C,2h 20min|
|49||0.25 C,3h 10min||none||0.25 C to 1.0V/cell|
|50||0.1 C,16h||1h-4h||0.2 C to 1.0V/cell|
|Cycle 1 to 50 shall be repeated until the discharges duration on any 50th cycle becomes less than 3hrs|
2. EXTERNAL APPEARANCE
The cell / battery shall be free from cracks, scars, breakage, rust, discoloration, leakage and deformation.
3. ELECTRICITY RETAINS:
Normal conditions with electricity retain 60%, if have special demands, confirm after negotiate.
One year limited warranty against workmanship and material defects.
5.1 Do not reverse charge batteries.
5.2 Do not short circuit batteries, permanent damage to batteries may result.
5.3 Do not subject batteries to adverse condition such as extreme temperature, deep cycling and excessive.
5.4 Store batteries in a cool dry place. Always discharge batteries before bulk storage or shipment.
5.5 Do not solder directly to cells or batteries.
5.6 If find any noise, excessive temperature or leakage from a battery, please stop its use.
5.7 Do not incinerate or mutilates batteries, may burst or release toxic material..
5.8 Do not mix new batteries in use with semi-used batteries, over-discharge may occur.
5.9 Do not remove the outer sleeve from a battery pack nor cut into its housing.
5.10 Never put a battery into water or seawater.
6.1 Batteries should be charged prior to use.
6.2 For charging methods please referred to our technical handbook.
6.3 Use the correct charger for Ni-MH batteries.
6.4 Avoid batteries being used in an airtight compartment. Ventilation should be provided inside the battery compartment, otherwise batteries may generate hydrogen gas, which could cause an explosion if exposed to an ignition source.
6.5 Do not attempt to take batteries apart or subject them to pressure or impact. Heat may be generated or fire may result. The alkaline electrolyte is harmful to eyes and skin, and it may damage clothing upon contact.
6.6 Keep away from children. If swallowed, contact a physician at once.
6.7 When using a new battery for the first time or after long term storage, please fully charge the battery before use.
6.8 When using a new battery in use with semi-used batteries, over-discharge may occur.
6.9 When the battery is hot, please do not touch it and handle it, until it has cooled down.
6.10 When find battery power down during use, please switch off the device to avoid over discharge.
6.11 Unplug a battery by holding the connector itself and not by pulling at its cord.
6.12 After use, if the battery is hot. Before recharging it, allow it to cool in a well-ventilated place out of direct sunlight.
7.1 In order to ensure the battery to maintain the capacity level, we suggest Ni-MH battery and battery pack should be stored under the condition of the -20 ~ 35 ℃, low humidity, no corrosive gases.
7.2 Ni-MH battery to avoid the high temperature or high humidity storage, otherwise it would lead to the battery leakage, rust, and the lower capacity.
7.3 The long-term storage may lead to NIMH batteries and battery packs to reduce the capacity and need 1-3 charge / discharge cycles to reach the maximum discharge capacity.
7.4 Three months after placing the battery need to be charge/discharge for one cycle.
Type:Rechargeable Nickel Metal Hydride
Nominal Dimension :Φ=14.5mm
(With sleeve) H=49.0mm
Applications: Recommended discharge current
200mA to 2000mA
Nominal Voltage: 1.2V
When discharged at 0.2C to 1.0V at 20℃
Charging Condition: 200mA for 16 hrs at 20℃
Fast Charge: 1000mA ~2000mA (0.5C~1C)
Charge termination control recommended
Control parameters: -△V: 5mV
dT/dt: 0.8℃/min (0.5 C)
dT/dt: 0.9℃/min (1 C)
Time: 105% nominal input
For reference only
Service life: ≥500 cycles (IEC standard)
Continuous: 200mA maximum current for 48 h
Overcharge: No conspicuous deformation
Weight: about 28.0g
Internal Resistance: Max 40mΩ Standard Charge
1hr rest at 1000HZ
Max. Charging Voltage: 1.5V at 200mA charging
ambient Temperature: Standard charging: 0 to 45℃
Fast charging: 10 to 45℃
Discharging: -20 to 60℃
Storage: -20 to 35℃
Contact Person: Frank Yu